Baldor DSM S Series Specifications Page 82
- Page / 122
- Table of contents
- TROUBLESHOOTING
- BOOKMARKS
Rated. / 5. Based on customer reviews
6-2 Troubleshooting MN1957
www.baldormotion.com
6.2 NextMove ESB-2 indicators
6.2.1 Status display
The Status LED normally displays the unit's node number. To display information
about a specific axis, use the LED keyword (see the Mint help file). When a
specific axis is selected, the following symbols may be displayed by the Status
LED. Some characters will flash to indicate an error.
Spline. A spline move is being performed. See the SPLINE keyword and related
commands.
Axis enabled.
Torque mode. The NextMove ESB-2 is in Torque mode. See the TORQUE keyword and
related commands.
Hold to Analog. The axis is in Hold To Analog mode. See the HTA keyword and related
commands.
Follow and offset. When an axis is following a demand signal it may be necessary to
advance or retard the slave in relation to the master. To do this an offset move is
performed in parallel with the follow. See the FOLLOW and OFFSET keywords.
Circle. A circle move is being performed. See the CIRCLEA or CIRCLER keywords.
Cam. A Cam profile is being profiled. See the CAM keyword.
General error. See the AXISERROR keyword. The motion toolbar displays the status of
AXISERROR, which is a bit pattern of all latched errors. See also the Error Log topics in
the help file.
Error input. The ERRORINPUT has been activated and generated an error.
Flying shear. A flying shear is being profiled. See the FLY keyword.
Position following error. A following error has occurred. See the AXISERROR keyword
and associated keywords. Following errors could be caused by a badly tuned drive/
motor. At higher acceleration and deceleration rates, the following error will typically be
greater. Ensure that the drive/motor is adequately tuned to cope with these
acceleration rates. The following error limit can be adjusted to suit your application (see
the FOLERRORFATAL and VELFATAL keywords). Following error could also be the
cause of encoder/resolver loss (see also the FEEDBACKFAULTENABLE keyword).
Follow mode. The axis is in Follow mode. See the FOLLOW keyword.
Homing. The axis is currently homing. See the HOME keyword.
Incremental move. An incremental move is being profiled. See the INCA and INCR
keywords.
Jog. The axis is jogging. In the Mint help file, see the topics JOG, JOGCOMMAND and
Jog mode.
- MN1957 NextMove ESB-2 1
- Contents 3
- 5 Operation 4
- 6 Troubleshooting 4
- Appendices 5
- General Information 7
- 1 General Information 7
- Safety Notice 8
- Precautions 8
- 2.1 NextMove ESB-2 features 9
- 2-2 Introduction MN1957 10
- 2.2 Receiving and inspection 11
- 2.3 Units and abbreviations 12
- 3.1 Introduction 13
- 140 (5.51) 14
- 124 (4.9) 14
- 45 (1.8) 14
- 4.1 Introduction 17
- 4.1.1 Connector locations 18
- 4.2 Analog I/O 19
- 4.2.2 Analog outputs 21
- , Flex+Drive 22
- , MintDrive 22
- 4.3 Digital I/O 23
- 4-10 Input / Output MN1957 26
- MN1957 Input / Output 4-11 27
- 4.3.2 Digital outputs 28
- 4.4 Other I/O 29
- 4-14 Input / Output MN1957 30
- 4.4.3 Encoder inputs 0-4 31
- 4-16 Input / Output MN1957 32
- 4.4.4 Relay connections 34
- 4.4.5 USB port 34
- 4.4.6 Serial port 35
- 4.4.7 Using RS232 35
- 4-20 Input / Output MN1957 36
- MN1957 Input / Output 4-21 37
- 4.5.1 CAN connector 38
- 4.5.2 CAN wiring 39
- 4.5.3 CANopen 40
- MN1957 Input / Output 4-25 41
- 4.5.4 Baldor CAN 42
- MN1957 Input / Output 4-27 43
- MN1957 Input / Output 4-29 45
- 4-30 Input / Output MN1957 46
- 5.1 Introduction 47
- 5.1.4 Preliminary checks 48
- 5.1.5 Power on checks 48
- 5.2 Mint Machine Center 49
- 5.2.1 Starting MMC 50
- 5.3 Mint WorkBench 51
- 5.3.1 Help file 52
- 5.3.2 Starting Mint WorkBench 53
- 5-8 Operation MN1957 54
- 5.4 Configuring an axis 55
- 5.4.2 Selecting a scale 56
- MN1957 Operation 5-11 57
- 5-12 Operation MN1957 58
- 5.5 Stepper axis - testing 59
- 5-14 Operation MN1957 60
- MN1957 Operation 5-15 61
- 5-16 Operation MN1957 62
- MN1957 Operation 5-17 63
- 5-18 Operation MN1957 64
- MN1957 Operation 5-19 65
- 5-20 Operation MN1957 66
- 5.7.2 Underdamped response 67
- 5.7.3 Overdamped response 68
- MN1957 Operation 5-23 69
- 5.8.1 Calculating KVELFF 70
- MN1957 Operation 5-25 71
- 5-26 Operation MN1957 72
- 5.8.2 Adjusting KPROP 73
- 5-28 Operation MN1957 74
- MN1957 Operation 5-29 75
- 5-30 Operation MN1957 76
- MN1957 Operation 5-31 77
- 5.11 Saving setup information 78
- MN1957 Operation 5-33 79
- 5-34 Operation MN1957 80
- 6.1 Introduction 81
- 6.2 NextMove ESB-2 indicators 82
- 6.2.2 Communication 83
- 6.2.3 Motor control 84
- MN1957 Troubleshooting 6-5 85
- 6.2.4 Mint WorkBench 86
- 6.2.5 CANopen 87
- 6-8 Troubleshooting MN1957 88
- 6.2.6 Baldor CAN 89
- 6-10 Troubleshooting MN1957 90
- 7.1 Introduction 91
- 7.1.4 Digital inputs 92
- 7.1.6 Relay output 92
- 7.1.7 Stepper control outputs 93
- 7.1.8 Encoder inputs 93
- 7.1.9 Serial RS232/RS485 port 93
- 7.1.10 CAN interface 94
- 7.1.11 Environmental 94
- 7.1.12 Weights and dimensions 94
- EC Declaration of Conformity 95
- 7-6 Specifications MN1957 96
- A.1 Introduction 97
- A.1.2 Baldor CAN nodes 98
- A.1.3 HMI panels 99
- A.1.4 Baldor keypad 99
- A-4 Accessories MN1957 100
- B.1 Introduction 101
- MN1957 Index 115
- Index MN1957 116
- Comments 119
- Comments MN1957 120
Related products and manuals for Steppers Baldor DSM S Series
Steppers Baldor DSM S Series User Manual
(24 pages)
(24 pages)
Steppers Baldor DSM S Series User Manual
(4 pages)
(4 pages)
Steppers Baldor DSM S Series Specifications
(34 pages)
(34 pages)
© 2020, manymanuals.com. All rights reserved. | 1.576 s |
Manymanuals.com
Manymanuals.de
Manymanuals.fr
Manymanuals.it
Manymanuals.pl
Manymanuals.cz
Manymanuals.es
Manymanuals-pt.com
Comments to this Manuals