Baldor DSM S Series Specifications Page 75
- Page / 122
- Table of contents
- TROUBLESHOOTING
- BOOKMARKS
Rated. / 5. Based on customer reviews
MN1957 Operation 5-29
www.baldormotion.com
5.9 Servo axis - eliminating steady-state errors
In systems where precise positioning accuracy is required, it is often necessary to position
within one encoder count. Proportional gain, KPROP, is not normally able to achieve this
because a very small following error will only produce a small demand for the drive amplifier
which may not be enough to overcome mechanical friction (this is particularly true in current
controlled systems). This error can be overcome by applying integral gain. The integral
gain, KINT, works by accumulating following error over time to produce a demand sufficient
to move the motor into the required position with zero following error. KINT can therefore
overcome errors caused by gravitational effects such as vertically moving linear axes. With
current controlled drive amplifiers a non-zero demand output is required to hold the load in
the correct position, to achieve zero following error.
Care is required when setting KINT since a high value will cause instability during moves.
A typical value for KINT would be 0.1. The effect of KINT should also be limited by setting the
integration limit, KINTLIMIT, to the smallest possible value that is sufficient to overcome
friction or static loads, for example 5. This will limit the contribution of the integral term to 5%
of the full demand output range.
1. Click in the KINT box and enter a small
starting value, for example 0.1.
2. Click in the KINTLIMIT box and enter a
value of 5.
With NextMove ESB-2, the action of KINT and KINTLIMIT can be set to operate in various
modes:
Never - the KINT term is never applied
Always - the KINT term is always applied
Smart - the KINT term is only applied when the demand speed is zero or constant.
Steady State - the KINT term is only applied when the demand speed is zero.
This function can be selected using the KINTMODE drop down box.
- MN1957 NextMove ESB-2 1
- Contents 3
- 5 Operation 4
- 6 Troubleshooting 4
- Appendices 5
- General Information 7
- 1 General Information 7
- Safety Notice 8
- Precautions 8
- 2.1 NextMove ESB-2 features 9
- 2-2 Introduction MN1957 10
- 2.2 Receiving and inspection 11
- 2.3 Units and abbreviations 12
- 3.1 Introduction 13
- 140 (5.51) 14
- 124 (4.9) 14
- 45 (1.8) 14
- 4.1 Introduction 17
- 4.1.1 Connector locations 18
- 4.2 Analog I/O 19
- 4.2.2 Analog outputs 21
- , Flex+Drive 22
- , MintDrive 22
- 4.3 Digital I/O 23
- 4-10 Input / Output MN1957 26
- MN1957 Input / Output 4-11 27
- 4.3.2 Digital outputs 28
- 4.4 Other I/O 29
- 4-14 Input / Output MN1957 30
- 4.4.3 Encoder inputs 0-4 31
- 4-16 Input / Output MN1957 32
- 4.4.4 Relay connections 34
- 4.4.5 USB port 34
- 4.4.6 Serial port 35
- 4.4.7 Using RS232 35
- 4-20 Input / Output MN1957 36
- MN1957 Input / Output 4-21 37
- 4.5.1 CAN connector 38
- 4.5.2 CAN wiring 39
- 4.5.3 CANopen 40
- MN1957 Input / Output 4-25 41
- 4.5.4 Baldor CAN 42
- MN1957 Input / Output 4-27 43
- MN1957 Input / Output 4-29 45
- 4-30 Input / Output MN1957 46
- 5.1 Introduction 47
- 5.1.4 Preliminary checks 48
- 5.1.5 Power on checks 48
- 5.2 Mint Machine Center 49
- 5.2.1 Starting MMC 50
- 5.3 Mint WorkBench 51
- 5.3.1 Help file 52
- 5.3.2 Starting Mint WorkBench 53
- 5-8 Operation MN1957 54
- 5.4 Configuring an axis 55
- 5.4.2 Selecting a scale 56
- MN1957 Operation 5-11 57
- 5-12 Operation MN1957 58
- 5.5 Stepper axis - testing 59
- 5-14 Operation MN1957 60
- MN1957 Operation 5-15 61
- 5-16 Operation MN1957 62
- MN1957 Operation 5-17 63
- 5-18 Operation MN1957 64
- MN1957 Operation 5-19 65
- 5-20 Operation MN1957 66
- 5.7.2 Underdamped response 67
- 5.7.3 Overdamped response 68
- MN1957 Operation 5-23 69
- 5.8.1 Calculating KVELFF 70
- MN1957 Operation 5-25 71
- 5-26 Operation MN1957 72
- 5.8.2 Adjusting KPROP 73
- 5-28 Operation MN1957 74
- MN1957 Operation 5-29 75
- 5-30 Operation MN1957 76
- MN1957 Operation 5-31 77
- 5.11 Saving setup information 78
- MN1957 Operation 5-33 79
- 5-34 Operation MN1957 80
- 6.1 Introduction 81
- 6.2 NextMove ESB-2 indicators 82
- 6.2.2 Communication 83
- 6.2.3 Motor control 84
- MN1957 Troubleshooting 6-5 85
- 6.2.4 Mint WorkBench 86
- 6.2.5 CANopen 87
- 6-8 Troubleshooting MN1957 88
- 6.2.6 Baldor CAN 89
- 6-10 Troubleshooting MN1957 90
- 7.1 Introduction 91
- 7.1.4 Digital inputs 92
- 7.1.6 Relay output 92
- 7.1.7 Stepper control outputs 93
- 7.1.8 Encoder inputs 93
- 7.1.9 Serial RS232/RS485 port 93
- 7.1.10 CAN interface 94
- 7.1.11 Environmental 94
- 7.1.12 Weights and dimensions 94
- EC Declaration of Conformity 95
- 7-6 Specifications MN1957 96
- A.1 Introduction 97
- A.1.2 Baldor CAN nodes 98
- A.1.3 HMI panels 99
- A.1.4 Baldor keypad 99
- A-4 Accessories MN1957 100
- B.1 Introduction 101
- MN1957 Index 115
- Index MN1957 116
- Comments 119
- Comments MN1957 120
Related products and manuals for Steppers Baldor DSM S Series
Steppers Baldor DSM S Series User Manual
(24 pages)
(24 pages)
Steppers Baldor DSM S Series User Manual
(4 pages)
(4 pages)
Steppers Baldor DSM S Series Specifications
(34 pages)
(34 pages)
© 2020, manymanuals.com. All rights reserved. | 1.341 s |
Manymanuals.com
Manymanuals.de
Manymanuals.fr
Manymanuals.it
Manymanuals.pl
Manymanuals.cz
Manymanuals.es
Manymanuals-pt.com
Comments to this Manuals